How to Contour Swales and Berms for Dryland Gardening

Contouring swales and berms across a sloped yard is one of the most effective ways to harvest rainwater for dryland gardening. This article explains how to evaluate your landscape, find the exact contour lines of your slope, and dig level trenches paired with raised soil mounds. By following these steps, you will learn how to slow down runoff, spread moisture evenly across your property, and sink water deep into the soil to create a self-sustaining, drought-resistant garden.

Understanding Swales and Berms

A swale is a shallow ditch dug completely level along the contour of a slope, and a berm is the mound of soil created on the downhill side of that ditch using the excavated dirt. Unlike traditional drainage ditches that are sloped to move water away from a property, a swale is entirely flat from one end to the other.

When it rains, water flows down the hill and gets trapped in the level swale. Because the swale is on a contour, the water cannot flow to one end and spill out. Instead, the berm holds the water back, forcing it to spread out evenly and slowly infiltrate the ground. This creates an underground reservoir of moisture that plant roots can access long after the rain stops.

Assessing Your Slope

Before digging, you need to evaluate the steepness and soil composition of your yard. Swales work best on gentle to moderate slopes, typically those with a grade between 3 percent and 15 percent. If a slope is too steep, concentrating water into a swale can saturate the ground too quickly and cause a mudslide.

Avoid placing swales within ten feet of building foundations, septic fields, or underground utility lines, as the increased deep-soil moisture can damage these structures. You should also begin your project at the highest point of your property and work your way down. Catching water at the top of the watershed reduces the volume and velocity of the water that reaches the lower sections of your yard.

Finding the Contour Line

For a swale to work, the bottom of the trench must be perfectly level. You can map the contour line of your slope using a simple DIY tool called an A-frame level, or a clear plastic tube filled with water known as a bungee level.

  1. Drive a wooden stake into the ground at the starting point of your desired swale, starting near the top of your slope.
  2. Place one leg of your A-frame level next to the first stake.
  3. Swing the other leg of the A-frame across the slope until the plumb line or spirit level in the center shows that both legs are sitting on ground of the exact same elevation.
  4. Drive a second stake into the ground at the spot of the second leg.
  5. Move the first leg of the A-frame to the second stake, and swing the other leg out to find the third point.
  6. Repeat this process all the way across the yard. The line of stakes will form a curve that represents the true contour of the land.

Digging the Swale and Building the Berm

Once your stakes are in place, connect the dots by marking the line with landscaping paint or a garden hose. This line represents the uphill edge of your swale.

Begin digging a trench along this line. For a standard residential yard, a swale is typically one to two feet wide and one foot deep. As you dig, pile all the excavated soil immediately on the downhill side of the trench to form the berm. Do not compact the soil on the berm; leave it loose so plant roots can easily penetrate it and water can wick into it.

Use a carpenter's level taped to a long, straight board to check the bottom of your trench as you dig. The bottom of the swale must be flat and level across its entire length so water collects evenly. The sides of the trench and the berm should be gently sloped rather than vertical, which prevents the dirt walls from collapsing during heavy rain.

Building an Overflow Spillway

Every swale needs a planned overflow route called a spillway. In the event of an extreme rainstorm, the swale may fill to capacity. Without a spillway, the water will breach the berm at its weakest point and wash away your hard work.

Create a spillway by making one small section of the berm—usually about two feet wide—slightly lower than the rest of the berm. Still, keep this section higher than the original ground level so the swale can hold water. Compact the soil on the spillway and armor it with flat rocks or heavy sod to prevent erosion when water flows over it. If you are building multiple swales down a slope, position the spillway so the excess water flows directly into the next swale below it.

Mulching and Planting

Never leave the soil of a new swale and berm bare, as wind and rain will quickly erode the loose dirt. Fill the bottom of the swale and cover the entire berm with a thick layer of organic woodchip mulch, straw, or leaves, aiming for a depth of four to six inches. The mulch slows down water, prevents evaporation, and gradually breaks down to build rich topsoil.

When planting, match your plants to the moisture zones you have created:

  • Uphill side of the berm: Plant trees, shrubs, and perennials that need the most water right at the inside base of the berm, where the soil stays wettest.
  • Top and downhill side of the berm: Plant native, drought-tolerant species and Mediterranean herbs higher up on the mound where the soil drains quickly and remains drier.
  • Inside the swale: Avoid planting directly in the bottom of the trench, as plants here may drown during heavy rains and can block the even spread of water.

As the roots of your trees and perennials grow into the berm, they will lock the soil in place, permanently stabilizing your earthworks and turning your dry slope into a thriving oasis.