How to Take Softwood vs Hardwood Cuttings to Clone Shrubs

Cloning shrubs like rosemary and hydrangea is an affordable and rewarding gardening method that relies on taking either softwood or hardwood stem cuttings. This article breaks down the fundamental differences between softwood and hardwood propagation, the ideal times of year to take each type of cutting, and the step-by-step techniques required to successfully root them into exact genetic copies of your favorite plants.

Understanding the Difference

The primary difference between softwood and hardwood cuttings is the maturity of the plant tissue and the season in which you take them.

  • Softwood cuttings are taken from the fresh, flexible, new growth of the current season in spring and early summer. They root quickly because the plant is actively growing, but they lose moisture fast and require high humidity to survive.
  • Hardwood cuttings are taken from mature, woody, dormant stems in late autumn or winter. They take several months to produce roots, but they are much hardier, require less daily maintenance, and do not dry out as easily.

How to Take Softwood Cuttings

Softwood propagation is the best method for summer-blooming shrubs like hydrangeas and actively growing herbs like rosemary. Take these cuttings in the morning when the plant is fully hydrated.

  1. Select the Stem: Look for healthy, non-flowering shootsfrom the current year’s growth. The stem should be flexible and snap cleanly when bent, rather than just folding over or being too woody to bend.
  2. Make the Cut: Using sanitized, sharp pruners, cut a 4 to 6-inch section of the stem. Make your cut just below a leaf node (the bump where the leaf meets the stem), as this area contains the highest concentration of root-producing hormones.
  3. Prepare the Cutting: Strip the leaves from the bottom half of the stem so no foliage will sit below the soil line. Leave two to four leaves at the very top. If cloning large-leafed shrubs like hydrangeas, cut the remaining top leaves in half horizontally to reduce water loss through evaporation.
  4. Apply Rooting Hormone: Dip the wet, bottom tip of the cutting into a rooting hormone powder or gel to speed up root development and prevent rot.
  5. Plant the Cutting: Poke a hole into a pot filled with a moist, soil-less medium like perlite, vermiculite, or coarse sand. Insert the cutting so the bottom nodes are buried, and gently firm the medium around the stem.
  6. Create Humidity: Water the pot gently and place a clear plastic bag over it to create a mini-greenhouse. Use sticks to keep the plastic from touching the leaves. Place the pot in bright, indirect sunlight.
  7. Aftercare: Keep the medium moist. Roots should form for rosemary and hydrangeas in 3 to 6 weeks. You will know roots have formed when you see new leaf growth or feel resistance when gently tugging the stem.

How to Take Hardwood Cuttings

Hardwood propagation works exceptionally well for deciduous shrubs like hydrangeas once they have dropped their leaves, and for established, woody rosemary stems. Do this between late fall and late winter when the plant is dormant.

  1. Select the Stem: Choose a healthy, pencil-thick stem that grew during the previous summer. It should be firm, brown, and woody, not green.
  2. Make the Cuts: Cut a section of stem that is 6 to 10 inches long. Make a flat, straight cut just below a bud node at the bottom of the cutting. Make a slanted, angled cut just above a bud node at the top of the cutting. This angled top cut helps shed rainwater and tells you which end goes up.
  3. Prepare the Cutting: Deciduous shrubs like hydrangeas will have no leaves to strip. For evergreen shrubs like rosemary, strip all the needles from the bottom two-thirds of the woody stem.
  4. Wound the Base: Lightly scrape a half-inch of the outer bark off one side of the very bottom of the stem. Exposing this green inner layer encourages thick callusing and root growth. Dip this wounded base into a strong rooting hormone formulated for hardwood.
  5. Plant the Cutting: You can plant hardwood cuttings in a deep pot filled with half potting soil and half perlite, or directly into a sheltered outdoor garden trench filled with sand. Bury the cutting so that only the top one-third (with the angled cut) is exposed above the soil.
  6. Aftercare: Water the cuttings thoroughly. If using pots, place them in an unheated garage, cold frame, or shaded area outside. Ensure the soil never completely dries out over the winter, nor becomes waterlogged. By late spring, the cuttings will break dormancy, grow leaves, and have an established root system ready for transplanting in the fall.